These data are for each LED in the table of Graph Spectral Characteristics:
Czech...................English
Napětí[V]..............Voltage [V]
Proud[mA].............Current [mA]
Výkon[W]..............Power [W]
Světelný tok[lm]....Luminous flux [lm]
Účinnost[lm/W].....Efficacy [lm/W]...
Measurements were previously published in the local forum:http://forum.fotonmag.cz/index.php?showtopic=886&st=0&start=0
Method of measurement and equipment
-Measurements are performed in the laboratory with an integration sphere and a spectrometer in the Technical University in Liberec.
-The...
Photos did not fit into the first report....
[IMG]
added electronics for constant current
[IMG]
SST-50 on a new cooler (glued using "Arcit Aluminia) and 0.5 mm aluminum sheet
[IMG]
0.5 mm aluminum plate on the SST-50
[IMG]
Hi Bob,
I have Romisen complete. I stuck SST-50 directly on a new cooler using "Arcit Aluminia" for perfect heat dissipation. And I made a cooler from above the SST-50 from 0.5 mm Al plate. This plate also divert heat to the Al reflector.
I have done thermal protection in Romisen by using PTC...
Re: Mag 3 "C" SST-90 MG aspherical with LDO10C Driver and 2 26650 IMR's 10 amps
Nice mod...:twothumbs
The voltade DC-DC switch is my idea. I used voltage DC-DC switch(30 amperes) with PTC thermistor for temperature compensation as the first in my Romisen@P7...
ANSWERs:
I make beamshots comparison with "standard'' flashlight during 7-14 days, I have exam now ...
Insulate reflector is not needed, but I use the thermal pads for transfer heat to the reflector ...
Romisen has 3mode, I can set 5-100W for every one of them
For 18,650 Emmerich is not...
I made a similar lamp here.
I finished Romisen at Christmas (more information on the local forum), but I had a problem with LEDs ... I had to re-solder LEDs, and I have not complete the Romisen now, because I have exams on university and a little time ...
I made this flashlight per order for...
I have at home 4 EMMERICH IHR18650 cells, these cells have stable voltage at high currents. On package is written, "Sony Lithium Ion Akku Mangan US18650V1 HBG", but probably they are not these cells " Sony US-18650-V "
Tests are from the local forum of "jirik cz", measured on the device with...
I found EMMERICH IHR18650 1500mAh - constant discharge current 10C and burst discharge current 15C(over 20A) batteries. These batteries, I found only on http://www.conrad.com/ (homepage Conrad is a German) - this site is credible...
EMMERICH IHR18650 batteries are on German sites (14,95 EUR) and...
I have ordered 25 pieces SSR-50-W57S-R21-GJ200 from EBV elektronik. Tomorrow I expect delivery. Price from EVB cca 24EUR /pc. Minimum order is 25 pieces.
I'm from the Czech Republic.
Techjunkie: The figure shows SMD case 0805. In this case may be resistor, thermistor, capacitor or inductor. The termistor is soldered on top PCB.
Driver is controlled by series-parallel combination of resistors and thermistor. Selecting the correct value of resistance is lengthy...
Al Combs...
For example I give voltage DC-DC switch without control thermistor and with control thermistor.
I measure voltage on resistor 4.3 miliohm and then I calculate the current.
- in Romisen were used poor and old 18650 2000mAh. (My TF 18650 I lost at home.):grin2: Higher currents were for 18650 death.
I have not at home arctic alumina adhesive or similar. I hurried and I put a thin microtene spacer(plastic)! Works perfectly. Paste is MX2. I measured the temperature of flashlight and simultaneously voltage on SSC P7. The temperature of flashlight was 49°C and voltage on SSC P7 is decreased...
I didn´t think about selling Romisen. I make flashlights for pleasure, but I can produce Romisen for you once again. Production would take one month. When you would like to buy Romisen earlier, I could sell you mine, but not to like. :) Costs for production Romisen 6x SSC P7 are cca 250$...