Test/Review of Charger Xtar VP4

HKJ

Flashaholic
Joined
Mar 26, 2008
Messages
9,715
Location
Copenhagen, Denmark
[size=+3]Charger Xtar VP4[/size]

DSC_7997.jpg

DSC_7999.jpg
DSC_7998.jpg


Xtar has many good LiIon chargers, this is a 4 channel charger in their advanced charge line: VP1: 2 slots, 3 currents and voltage display, VP2: 2 slots, 3 currents, 3 voltages, voltage display and usb out. This new model has 4 slots, 2½ currents and voltage display. Compared to VP2 only the number of slots and the maximum battery size has been improved, other features are the same or downgraded.



The charger comes in a cardboard box with lots of specifications on it.

DSC_7994.jpg


In the box is the charger, a power supply, a car adapter, a instruction manual and a warranty card.

DSC_8001.jpg


The charger has a DC connector for power input. Because it can only charge with 1A on two channel, it only need a 1A power adapter. If more channels are used all will be reduced to 0.5A.

DSC_8005.jpg
DSC_8007.jpg


The slots have raised battery connections, i.e. flat top batteries can be used. The slider works very smooth and can take batteries from 30.5mm to 71.5mm. This is enough to handle even long protected 26650 batteries.

DSC_8003.jpg


On the top of the charger is a switch to select charge current, it can select between 0.25A, 0.50A and 1.00A, the current will be the same in all four slots.
The charger will always select the highest possible current when loading it with batteries, the switch can then be used to reduce the current.
When only slot #1 and/or slot #4 is used the maximum current is 1A. If there is any batteries in slot #2 or #3 the maximum will be reduced to 0.5A.
Below the switch is the display, by holding the switch down the display can be turned off/on (but not the leds), this will not affect any function in the charger.

DSC_8011.jpg


The display captured during startup where everything is turned on.

DSC_8012.jpg


Regular charge, the battery symbol is animated when the charger is charging.

DSC_8027.jpg


The charger has a led for each channel, making it very easy to see when it is finished.


supportedBatteryTypes.png


supportedBatterySizes.png
DSC_8017.jpg
DSC_8018.jpg
DSC_8019.jpg

DSC_8020.jpg
DSC_8021.jpg
DSC_8022.jpg
DSC_8025.jpg
DSC_8024.jpg


The charger can easily handle 70 mm long batteries, inclusive flat top cells.



[size=+2]Measurements[/size]


  • Discharges LiIon with 0.2mA to 0.3mA when not connected to power
  • Charges with 0.2mA when LiIon battery is full.
  • Below 1 volt the charger will charge with 1mA, the display will be empty and the led green.
  • Between 1 and 2 volt the charger will charge with 33mA, the display will show voltage and the led will flash red.
  • Between 2 and 3 volt the charger will charge with 85mA, the display will show voltage and the led be red.
  • Above 3 volt regular charge current is used.
  • In the regular charge range the voltmeter is within 0.01 volt, at lower voltages the tolerance is slightly larger.
  • The meter updates the voltage reading fairly often (Better than once a second).
  • The meter stops updating above 4.20 volt when the charging stops.
  • Will restart if battery voltage drops below 3.90 volt.
  • Charge will restart charging after power loss or battery insertion.
  • If any battery is placed in either of the two center slots, the maximum charge current is reduced to 0.5A (A full battery in either center slow will also reduce the current).
  • When charger is powered on display shows 0.5A charge current, but charger will automatic change to 1A if a battery is put in slot #1 or #4.
  • Current select button will decrease current when pressed, i.e. 1A -> 0.5A -> 0.25A -> 1A


Xtar%20VP4%201A%20(PA18650-31)%20%231.png


First charge curve shows a very nice CC/CV curve with a termination about 80mA. This is a very good charge curve.

Xtar%20VP4%200.5A%20(PA18650-31)%20%232.png

Xtar%20VP4%200.5A%20(PA18650-31)%20%233.png

Xtar%20VP4%201A%20(PA18650-31)%20%234.png


The other channel does also work fine.

Xtar%20VP4%201A%20(BE18650-26)%20%231.png


Xtar%20VP4%201A%20(PA18650-34)%20%231.png


Different capacity batteries, need different charge time.

Xtar%20VP4%200.5A%20(PA18650-31)%20%231.png


Reducing the charge current to 0.5A, does reduce the termination current to about 40mA and uses the same good CC/CV curve.

Xtar%20VP4%200.25A%20(PA18650-31)%20%231.png


The 0.25A charge current uses a termination current of about 30mA.

Xtar%20VP4%201A%20(AW16340-IMR)%20%231.png


Trying to provoke the charger with my old 16340 cell does not show any problems, the charger handles it nicely.

Xtar%20VP4%200.25A%20(AW16340-IMR)%20%231.png


Reducing the charge current to the 16340, makes the curve more smooth.


Xtar%20VP4%200.5A%20(KP14500-08)%20%231.png


A 14500 cell at 0.5A works fine.

Xtar%20VP4%200.5A%20(AW18350-IMR)%20%231.png


Same with a 18350 at 0.5A.

Xtar%20VP4%200.5A%20(4xPA18650-31).png


With four cells the current is limited to 0.5A for all slots.

Xtar%20VP4%200.5A%2012V%20(4xPA18650-31).png


Using an external 12V supply, the charger draws nearly 1A while charging.

Temp1401.png


M1: 32,5°C, M2: 34,8°C, M3: 35,6°C, M4: 32,1°C, M5: 38,8°C, M6: 42,4°C, HS1: 43,4°C
With 0.5A charge current the batteries are not heated much.

Temp1400.png


M1: 33,0°C, M2: 35,0°C, M3: 35,3°C, M4: 32,9°C, M5: 44,6°C, HS1: 65,0°C
But inside some electronic do get warm.

Startup.png


The charger needs about 8 seconds to turn on and will always start charging at the highest possible current setting.

Charge.png


When selecting another charge current, the charger will decrease current fast and increase current slowly.



Testing the mains transformer with 2500 volt and 5000 volt between mains and low volt side, did not show any safety problems.



[size=+2]Conclusion[/size]

The charger can handle a wide range of battery sizes from 10440 up to 32650 batteries and has a good CC/CV charge curve. The display with the precise voltage readout makes it easy to check if batteries has been over discharged. The leds is a very nice feature, that makes it easy to see when batteries are charged.

It is a good charger with nice features, but not what many people had hoped for in a VP4 charger, i.e. 3 voltages and at least 3 currents.



[size=+3]Notes[/size]

The charger was supplied by Xtar for review.

Here is an explanation on how I did the above charge curves: How do I test a charger
 

SubLGT

Flashlight Enthusiast
Joined
Nov 18, 2013
Messages
1,183
Location
Idaho, USA
Other than the cost disadvantage, it seems a person would be better served with a pair of Xtar VP2 chargers, than a single VP4.
 

SubLGT

Flashlight Enthusiast
Joined
Nov 18, 2013
Messages
1,183
Location
Idaho, USA
…..Because it can only charge with 1A on two channel, it only need a 1A power adapter……...

If it can charge 2 channels simultaneously at 1A each, why does it not need a 2A power supply?
 

StandardBattery

Flashlight Enthusiast
Joined
Sep 2, 2007
Messages
2,959
Location
MA
If it can charge 2 channels simultaneously at 1A each, why does it not need a 2A power supply?
Output power and input power, but the input voltage is 12V the charging voltage is less. It's internal DC-DC converters handle the conversion while maintaining a high power conversion efficiency so more current is available on the output as power uniformity is maintained.
 
Last edited:

zaturno1965

Newly Enlightened
Joined
Mar 27, 2015
Messages
1
in-depth review for the VP4 pls!Good day!

As a vaper with a dual battery APV, leaning towards sub ohming for more vapors, has me going thru my 3 pairs of 18650 batteries fairly quickly. So i decided to buy a VP4. As i read the instructions, i got interested in it's capability of charging ni-mh batteries, so i also bought a pair of Sanyo 2700mah AAs to use on my wireless mouse (and also for my wallclock ;) ). Could anyone explain, in-depth, this feature on the VP4? :help:
 
Last edited by a moderator:

ven

Flashaholic
Joined
Oct 17, 2013
Messages
22,533
Location
Manchester UK
Well added to my charger family with the vp4,love the display of the vp1 and vp2 so why not.........

Some 30q to throw in it as well


Of course other than not allowing 1a charge on all 4 which we know about(can get round that easy)
The centre 2 bays 2+3 are to close to get out for me without removing the outer cells first,i would have prefered even spacing to aid removal. Maybe others have no issues(might not bight their nails:whistle:) Understand wider on bays 1+4 for 26650 cell,thumbs up,just could have spaced middles out more imo anyway.

To get around charging 4 cells i just use my other Xtars


These are my down stairs chargers sat next to me now for ease,i have another 4 up stairs and 3 in work...........chargaholic i think :laughing:

Thanks ven:)
 

ven

Flashaholic
Joined
Oct 17, 2013
Messages
22,533
Location
Manchester UK
Narrow bays........well as said to me anyway,


Can see from the 2+3 + end they are a little closer.............other than that i like!
 
Top