Test/review of Nitecore Intellicharger new i4 2017

HKJ

Flashaholic
Joined
Mar 26, 2008
Messages
9,715
Location
Copenhagen, Denmark
[size=+3]Nitecore Intellicharger new i4 2017[/size]

DSC_1152.jpg


DSC_1153.jpg
DSC_1154.jpg


This is Nitecores "simple" charger in the 4 slot version.



The cardboard box lists lot of specifications, battery types and features.

DSC_1145.jpg


The box contains the charger, a mains cable, manual and a warranty card.

DSC_1155.jpg


The charger has two power connectors, one for mains input (100-250VAC 50/60Hz) and one for 9-12 VDC input.

DSC_1157.jpg


The user interface has buttons and the leds are place behind a dark cover.

DSC_1209.jpg



It has 3 green status leds and a red led to signal full current (1.5A). The status led also has a secondary function, they are used as indicators for selected voltage.
The charger is a bit special with current selection, usual it will select current depending on battery length and chemistry, but it can be overridden in one case: Two long LiIon batteries can be charged at 1.5A, but then they will be charged in sequence, not simultaneously.
To change voltage or current tap the C button until a single green led above the required slot lights up. Then hold C or V button to adjust current or voltage. C button can only turn the red led on, the V button will change between the 3 green leds for the 3 different LiIon charge voltages. Press again shortly on C or wait for timeout.

DSC_1158.jpg
DSC_1159.jpg


The slots uses the usual construction and works well. They can handle batteries from 28mm to 70mm long.
Notice the long bar at the plus end, due to this the charger can handle anything up to D or 32xxx size.

supportedBatteryTypes.png


supportedBatterySizes.png
DSC_1198.jpg
DSC_1199.jpg
DSC_1200.jpg
DSC_1201.jpg


DSC_1202.jpg
DSC_1203.jpg
DSC_1204.jpg
DSC_1205.jpg
DSC_1206.jpg
DSC_1207.jpg


The charger can handle 70 mm long batteries, inclusive flat top cells.


[size=+2]Measurements[/size]


  • Power consumption when idle is 0.56 watt
  • Will charge a LiIon with 0.2mA when charging is finished.
  • Will discharge a NiMH with 0.1mA when not powered
  • Will discharge a LiIon with 0.9mA when not powered
  • Change between long/short cell at around 56mm
  • Below 0.8V the charger will report error (All leds flashing) and charge with about 1mA.
  • Above 0.8V regular charging is used.
  • Will assume LiIon above 2.0V
  • Slot 1 & 3 will time share.
  • Slot 2 & 4 will time share.
  • Charger will not restart if battery voltage drops.
  • Power cycling and insertion of a battery will restart charging.


[size=+1]4.2V LiIon charging[/size]

Nitecore%20new%20i4%20%28SA18650-33%29%20%231.png


This is a nice CC/CV charge curve, the termination is slightly high at 200mA.

Nitecore%20new%20i4%20%28SA18650-33%29%20%232.png

Nitecore%20new%20i4%20%28SA18650-33%29%20%233.png

Nitecore%20new%20i4%20%28SA18650-33%29%20%234.png


The other 3 slots looks similar.


Nitecore%20new%20i4%20%28SA18650-26%29%20%231.png

Nitecore%20new%20i4%20%28PA18650-31%29%20%231.png


The two other batteries also charges fine.

Nitecore%20new%20i4%20%28BE18650-26%29%20%231.png


The old battery has more voltage drop when finished.

Nitecore%20new%20i4%20%28KP14500-08%29%20%231.png


With a smaller cell the current is automatically reduced to 0.5A, but the termination current stays the same.

Nitecore%20new%20i4%20%28AW18350-IMR%29%20%231.png


The charger has no problem with this old cell, but due to the high termination current the voltage will drop significantly when current is turned off.

Nitecore%20new%20i4%20%284xSA18650-33%29.png


With 4 batteries the charge current is fairly low.

Nitecore%20new%20i4%2012V%20%284xSA18650-33%29.png


And it need abou 0.8A from 12V

Temp4591.png


M1: 32,0°C, M2: 35,3°C, M3: 37,7°C, M4: 36,9°C, M5: 52,3°C, HS1: 72,3°C
The hot part is probably the internal power supply.

Temp4592.png


M1: 31,6°C, M2: 35,0°C, M3: 37,3°C, M4: 36,7°C, M5: 53,5°C, HS1: 84,4°C

PoweronLiIon1.png


The charger starts very fast. It turns current off to measure voltage.

ChargeLiIon14.png


With batteries in slot 1 & 4 it will only charge with half current, i.e. 0.75A

ChargeLiIon24.png


If I put batteries in slot 2 & 4 the current is also half, this time due to time sharing.

ChargeLiIon1234.png


With 3 or 4 batteries it will both reduce current and time share.



[size=+1]3.6V LiIon charging (LiFePO4)[/size]

Nitecore%20new%20i4%20%2818650-LiFePO4%29%20%231.png


Nitecore%20new%20i4%20%28SO14500-LiFePO4%29%20%231.png


The charger handles LiFePO4 batteries correctly.



[size=+1]4.35V LiIon charging[/size]

Nitecore%20new%20i4%20%28LG18650-30%29%20%231.png


The 4.35V charging looks fine.



[size=+1]NiMH charging[/size]

Nitecore%20new%20i4%20%28eneloop%29%20%231.png


With NiMH the charger current is only 0.5A for any size battery. The charging uses voltage termination without any top-off charge. I cannot see any temperature raise at the end of charge, i.e. the battery is slightly undercharged.

Nitecore%20new%20i4%20%28eneloop%29%20%232.png

Nitecore%20new%20i4%20%28eneloop%29%20%233.png

Nitecore%20new%20i4%20%28eneloop%29%20%234.png


The 3 other slots works the same way.

Nitecore%20new%20i4%20%28eneloopPro%29%20%231.png

Nitecore%20new%20i4%20%28powerex%29%20%231.png


Same with the two high capacity batteries.

Nitecore%20new%20i4%20%28eneloopXX%29%20%231.png


This worn down cell got 7.5 minutes before the charger realized that it was hopeless and terminated.

Nitecore%20new%20i4%20%28eneloopAAA%29%20%231.png


The AAA cell is charged the same way.

Nitecore%20new%20i4%20full%20%28eneloop%29%20%231.png


The full cell was detected in about 6 minutes.

Nitecore%20new%20i4%20%284xeneloop%29.png


With 4 batteries the charger current is about 0.375A, this time at least one battery gets warm (i.e. it is full).

Nitecore%20new%20i4%2012V%20%284xeneloop%29.png


The charger needs about 0.5A from 12V for charging four NiMH.

Temp4608.png


M1: 33,2°C, M2: 38,0°C, M3: 43,3°C, M4: 43,9°C, HS1: 72,0°C

Temp4609.png


HS1 87,1°C
Some electronic inside the charger gets fairly warm.

PoweronNiMH1.png


The charger is also fast to start with NiMH batteries.

ChargeNiMH24.png


With batteries in slot 2 & 4 the charger increased the current to 0.75A and starts time sharing.

ChargeNiMH1234.png


The charger do not reduce charge current with more batteries, 4 batteries use the same time sharing as two.

Testing with 2830 volt and 4242 volt between mains and low volt side, did not show any safety problems.



[size=+2]Conclusion[/size]

The charger is simple to use with the automatic current selection and chemistry selection: just put batteries in and they are charged.
But it is not a fast charger, a single 18650 can be charged in about 3 hours (This is fairly standard), but with four cell it will take 9 hours.
Charging LiFePO4 or 4.35V batteries is a bit more tricky due to the not very user friendly user interface, but it is possible.

I will call it a good family charger, everybody can use it for NiMH and 4.2V LiIon batteries.



[size=+2]Notes[/size]

The charger was supplied by a zapals.com for review.

Here is an explanation on how I did the above charge curves: How do I test a charger
 
Top