Recent content by jon_slider

Gather App
Candle Power Forums

Help Support Candle Power:

  1. J

    First Impressions Skilhunt H150 V4 with 519a 5000K LED.

    I think the Skilhunt UI is the most user friendly choice for a newbie. I recommend teaching them to use Physical Lockout. The H150 V4, uses a buck/boost driver.. it is more efficient, and runs cooler, than the V3 Linear driver.. The optic has not changed, imo the beam is excellent, and the...
  2. J

    First Impressions Skilhunt H150 V4 with 519a 5000K LED.

    Received this Skilhunt H150 V4 with the new Buck Boost Driver that promises to be more efficient, with more constant output, cooler running, and with higher maximum output than the previous version. The 5000K color temperature and neutral tint are excellent for a task light. The beam has nice...
  3. J

    What was the last LED light you purchased and why?

    I hope you enjoy the KR1AA clip option. Fwiw Vaseline does not conduct electricity. But it will probably get scraped out of the way from the pressure of closing the tailcap. No harm in trying.
  4. J

    Who Is A Fan: Rosy

    Negative DUV at 5000k is more rosy than at 2700k, which is more orange
  5. J

    Who Is A Fan: Rosy

    Team anti-green for me ;-)
  6. J

    What was the last LED light you purchased and why?

    good idea.. a copper washer would work too, if you figure out what size works, please share info I dont have either of those things, but I do have solder wick ;-)
  7. J

    What was the last LED light you purchased and why?

    good warning.. might be prudent to put a bit of solder on the ends of the solder wick, so they dont fray. It is still in the testing phase, but the solder wick spacer and KR1AA clip are working so well, Im inclined to keep them installed. Im keeping the tail closed and changing batteries...
  8. J

    What was the last LED light you purchased and why?

    thank you for explaining how things work for you in Europe Im very lucky here in USA I only pay the price shown on Hanks site.. nothing is added after it arrives. My most recent purchase is a Polished Silver Dual Channel D3AA w NTG35 4200K and Red with metal button, magnet and clip, for $48...
  9. J

    What was the last LED light you purchased and why?

    so for a Hanklight D4K with clip, cost is $42, so you would pay 0 shipping, 10.7% duty in Norway, and 25% Vat, for a total of $58 correct?
  10. J

    What was the last LED light you purchased and why?

    $400 in fees for a $45 light? Are you sure there is not some sort of misunderstanding? Emisar shipping is free for items over $40
  11. J

    The Official Zebralight Thread

    data posted by krug1972 shows his Opple measured some SC70 Frequencies (547Hz and 400Hz), that are similar to what thefreeman is reporting: ~400~1000Hz ripple
  12. J

    I dont have a problem, I can stop any time I want to. How about you?

    have not tried, sounds very nice.. I went as far as 2700K, and then recently switched to a Red Mix:
  13. J

    The Official Zebralight Thread

    Clic to read the whole SC70 driver Analysis posted by thefreeman: Here are the Cliff Notes: "Conclusion To improve this driver, Zebralight needs to: * get rid of low modes visible flicker * Get rid of the ~400~1000Hz Riple by increasing the PWM control signal frequency * fix the low modes...
  14. J

    My next AA/14500 Anduril light has been announced

    Note that on early versions of the D3AA the O ring sits lower. Newer versions have the O ring sitting higher, leaving plenty of room for the clip, and the O ring remains completely covered by the tailcap:
  15. J

    My next AA/14500 Anduril light has been announced

    yes, it goes on easily, and there is enough room to fit the top of the clip over a jeans seam, snugly.. easier to slide all the way into the upper bend of the clip with slacks that have thinner material than jeans.. but both materials work fine
See more

Latest posts

Back
Top