Recent content by Fixmaster-J
-
F
Introducing "PTS2"
Check out the sandwich shoppe: http://theledguy.chainreactionweb.com/product_info.php?cPath=48_56_73&products_id=606 They might have what you are looking for.- Fixmaster-J
- Post #50
- Forum: Homemade and Modified Flashlights Discussion
-
F
Hey H222A, I was hoping you could help me with a heatsink (mag D) for an osram ostar led...
Hey H222A, I was hoping you could help me with a heatsink (mag D) for an osram ostar led... Hope to hear from you. Cheers Jasper- Fixmaster-J
- Profile post
-
F
Did you get the test Newsletter?
Just received newsletter- Fixmaster-J
- Post #26
- Forum: Candle Power Forums Vendor Display
-
F
Magswitch Screw needed!!!
Have send an email to mag, but no reply so far :(- Fixmaster-J
- Post #5
- Forum: General Flashlight Discussion
-
F
Magswitch Screw needed!!!
Hi, Ive just lost the screw that goes into the mag (3D) switch (to hold it in place). Anyone got one for me? It sure would be apreciated! Tnx, Jasper- Fixmaster-J
- Thread
- Replies: 4
- Forum: General Flashlight Discussion
-
F
Sold/Expired High current 3AA>1D - 18AA>6D battery adapters.
Adapter arrived today. Havent had time to test it yet. Tnx- Fixmaster-J
- Post #173
- Forum: Sold/Expired/Completed
-
F
Sold/Expired Osram Ostar 1000 Lumen LED's LE UW E3B *None Available*
Oh so would i needing 1 shark for each osram? Or can i use a setup like: http://www.candlepowerforums.com/vb/showthread.php?t=201392&highlight=buckpuck I'm build a 3 P7 mag, would a 3*osram mag be much better? And whats the min/max Vin? J- Fixmaster-J
- Post #28
- Forum: Sold/Expired/Completed
-
F
Sold/Expired Osram Ostar 1000 Lumen LED's LE UW E3B *None Available*
Hi Mac, Is it possible to drive a LE UW E3B with a shark? Any ideas what to use for 3x LE UW E3B in a mag 3d?- Fixmaster-J
- Post #26
- Forum: Sold/Expired/Completed
-
F
Sold/Expired High current 3AA>1D - 18AA>6D battery adapters.
I'll have a 9AA>3D please! That would work great with my tri-P7 mag!! Paypal send $27,- :paypal:- Fixmaster-J
- Post #169
- Forum: Sold/Expired/Completed
-
F
12AA to 3D holder needed
No emitter. A HID car bulb..- Fixmaster-J
- Post #11
- Forum: Flashlight Electronics - Batteries Included
-
F
12AA to 3D holder needed
Re: 12AA to 3D Ive tried putting 4 eneloops in the barerel, and that fits. Now i have to find some way to wire them all in series and hold them together. If i solder them together then i have to find a way to charge them all at once. I think making somekind of battery holder is the best...- Fixmaster-J
- Post #5
- Forum: Flashlight Electronics - Batteries Included
-
F
12AA to 3D holder needed
Hi, Im looking for a "cheap" (DIY) battery holder for 12AA's in series that fits a mag 3D. Or Are there better options that dont cost much. Ill need about 12-16V and at leat 3Ah.- Fixmaster-J
- Thread
- Replies: 10
- Forum: Flashlight Electronics - Batteries Included
-
F
Sold/Expired High current 3AA>1D - 18AA>6D battery adapters.
Hi, Sry PM aswell. Do you have 12AA to 3d holders? I migt need 9AA to 3d aswell, they would have to be shiped to the netherlands.- Fixmaster-J
- Post #156
- Forum: Sold/Expired/Completed
-
F
How to make a cheap Bat-signal?
Hi, I know this is an old post. But i just found yours while i was looking on cpf. Take a look at this: http://www.candlepowerforums.com/vb/showthread.php?t=204452 Maybe you've allready finished your light. :wave:- Fixmaster-J
- Post #6
- Forum: Spotlights and HID Flashlights
-
F
Tri P7 mag, advice needed
Hey looks good, tnx! ill look into that!- Fixmaster-J
- Post #3
- Forum: LED Flashlights
