Sold/Expired Sinner Customs - Tri-EDC's and more - this run CLOSED

[mossyoak]

Re: Sinner Customs - Tri-EDC's and more.

Been looking around. Has anyone done any runtime tests? I've got a ti 18350 with FET driver and XP-L's. Running Efest 700MaH cells. Just curious what to expect on run times for the different levels.

 

[sinner-cpf]

Re: Sinner Customs - Tri-EDC's and more.

Runtimes are quite similar on all builds at the first three modes (moonlight 5-7mA, Low 0.15A, Medium 0.5A)

while high mode on the Nanjg-105c drivers are 1.4Amps after it steps down gradually from the 3.04A turbo 60s,
whereas in case of max lumens setup with FET driver, the high mode is 2.25Amps, with Turbo30s 9A+

once the low battery indicator kicks in, it wont let you access the turbo mode, this is done to keep enough juice left for the batteries to function properly on the lower modes over a prolonged period of time, trust me you will have a hard time exhausting all of the batteries and 18350's can run for hours on low setting with around 110lm otf.

 

[Tixx]

Re: Sinner Customs - Tri-EDC's and more.

Do you have the dimensions of the light? Can you do AL?

 

[sinner-cpf]

Re: Sinner Customs - Tri-EDC's and more.

3.1" - 18350
4.2" - 18650

Al is no longer being made.

 

[zeppo]

Re: Sinner Customs - Tri-EDC's and more.

Awesome new way to order... Harder to make mistakes this way

and grants on the popularity, it must be well earned

 

[light-modder]

Re: Sinner Customs - Tri-EDC's and more.

Are the short clips not available anymore?

 

[sinner-cpf]

Re: Sinner Customs - Tri-EDC's and more.

I have a few small clips left in case anyone asks.. but i wont be restocking them.

 

[Str8stroke]

Re: Sinner Customs - Tri-EDC's and more.

Aged Copper

 

[qmtu]

Re: Sinner Customs - Tri-EDC's and more.

Could someone direct me to some info on how many lumen is put out by each light engine.
Thanks.

 

[didi_1606]

Re: Sinner Customs - Tri-EDC's and more.

@qmtu try first page #25
@Str8stroke what did you put in the hole of the clip? Bead/rubber for not touching the copper body??

 

[qmtu]

Re: Sinner Customs - Tri-EDC's and more.

Thanks.
What's the difference between the XP-E2 and the Nichia 219B?

 

[qmtu]

Re: Sinner Customs - Tri-EDC's and more.

Wow I just corresponded by email with Sinner. I had a question about my order, and each time he responded by email within 5 minutes.
That's some awesome customer service.
I'm glad I got in early with his business.
Let's treat him gently so he doesn't get burned out like some others.

 

[DellSuperman]

Re: Sinner Customs - Tri-EDC's and more.

Thanks.
What's the difference between the XP-E2 and the Nichia 219B?

XP-E2 has a slightly smaller & tighter beam pattern as compared to the N219B..

 

[DellSuperman]

Re: Sinner Customs - Tri-EDC's and more.

Does anyone know if the tailcap is supposed to be water resistant?

I had to wash my Ti 18350 recently & i only dried the exterior after washing. After a couple of days, the light started to flicker & i found out that it was caused by the switch.
Apparently some water got in & caused some mild corrosion on the switch & brass pieces.
After drying the parts & cleaning up the stains, it was able to work normally for a short while before the flickering starts again.
So long story short, i have replaced the switch & its all good but I'm not ready to put the light anywhere near water...

 

[sinner-cpf]

Re: Sinner Customs - Tri-EDC's and more.

It should not happen, it would be possible if the rubber boot is not sealed properly or is broken/ruptured..

 

[DellSuperman]

Re: Sinner Customs - Tri-EDC's and more.

It should not happen, it would be possible if the rubber boot is not sealed properly or is broken/ruptured..

The rubber boot isn't broken. We shall see again if if the same thing happen since i use my light in a dirty environment & washing comes often.

I've replaced a new switch & tightened everything up nicely. Lets hope for the best..

 

[icestud]

Re: Sinner Customs - Tri-EDC's and more.

Can anyone tell me if you select the Trit option do the trits also come with it or just the slots?

 

[Eric242]

Re: Sinner Customs - Tri-EDC's and more.

Just the slots.

 

[icestud]

Re: Sinner Customs - Tri-EDC's and more.

Just the slots.

Thanks!

 

[sinner-cpf]

Re: Sinner Customs - Tri-EDC's and more.

Shipping orders this week, appreciate the patience of you good folks.
we're back on schedule and queue is finally cleared, turnaround time for this month is 1-2 weeks.

Thanks.