Weird Experience - Emisar Became Ghost Light

[Orion]

Yesterday, when I got home from work, I was putting my keys, wallet, flashlight, etc on the place next to the front door. That day I wore an outfit that caused me to take my green Emisar. Yes,...........I color code my EDC. I'll give you all a moment to process that.......

Okay, so anyway, I looked at my grey Emisar, sitting where it usually sits, and it was on low. I pushed the button to turn it off, and it didn't do anything. So I pressed it again, and it flashed like a strobe light. I messed with it some, and eventually it went off. I set it down, and it went full bright on its own. I pushed the button again to turn it off. I again turned itself on bright. This time, I held the button so it would go down to its lowest setting, then clicked it off. Again, it immediately turned on and went to full.
I took the battery out to see if it were low, but it was near full charge. I took the battery out of the green Emisar and switched them between the two. Both acted normal. I switched batteries again, and both acted normal. It hasn't done this again since. But when I'm gone, I am now scared it might happen to another of my Emisar flashlights. I have 5 in total. I wouldn't want to be away from home and one turn on full bright and potentially damage the light.

So, what do you think it was? Some weird error in the electronics.........or a ghost trying to communicate with me, yesterday?

As a related side note, this same flashlight has an odd thing about it. All my Emisar, when you click the switch, you hear two "clicks", one when pressing, and the other when you release. With this grey one, there is another "click" after the second,...when the button is released.

 

[jon_slider]

turned itself on bright.

Possible metal filings causing a short?

Interventions include,
1. cleaning out all old lube that may be contaminated with metalic particles..
2. close visual inspection under magnification looking for metal fragments between the driver and head, and between tailcap board that has the spring on it, and the tailcap..
3. if you have compressed air, blow out those gaps

With this grey one, there is another "click" after the second,...when the button is released.

Possible loose switch retaining ring or loose tailspring retaining ring, or loose retaining ring in the head, if your light has one?

intervention includes
1. using a tool to check the retaining rings are tight

Possible switch is staying pressed (if it has a metal switch button)?

intervention includes
1. close observation to note if metal switch button is rebounding freely and not sticking around the edges
2. inspect for lint or dirt particles stuck around the edge of the metal switch button

Things it is not:
1. Poltergeist
2. Battery

 

[dc38]

Yesterday, when I got home from work, I was putting my keys, wallet, flashlight, etc on the place next to the front door. That day I wore an outfit that caused me to take my green Emisar. Yes,...........I color code my EDC. I'll give you all a moment to process that.......

Okay, so anyway, I looked at my grey Emisar, sitting where it usually sits, and it was on low. I pushed the button to turn it off, and it didn't do anything. So I pressed it again, and it flashed like a strobe light. I messed with it some, and eventually it went off. I set it down, and it went full bright on its own. I pushed the button again to turn it off. I again turned itself on bright. This time, I held the button so it would go down to its lowest setting, then clicked it off. Again, it immediately turned on and went to full.
I took the battery out to see if it were low, but it was near full charge. I took the battery out of the green Emisar and switched them between the two. Both acted normal. I switched batteries again, and both acted normal. It hasn't done this again since. But when I'm gone, I am now scared it might happen to another of my Emisar flashlights. I have 5 in total. I wouldn't want to be away from home and one turn on full bright and potentially damage the light.

So, what do you think it was? Some weird error in the electronics.........or a ghost trying to communicate with me, yesterday?

As a related side note, this same flashlight has an odd thing about it. All my Emisar, when you click the switch, you hear two "clicks", one when pressing, and the other when you release. With this grey one, there is another "click" after the second,...when the button is released.

If it's a side switch button, can you get the retaining ring off to check it? Like @jon_slider mentioned, it could very well be a short that's triggering the light to believe that the switch has been pressed. Sometimes from the factory, there may be super thin strands of copper that are bridging connections that should not be bridged