When recently I got my Preon 1, a quick check of lumens and battery current showed results far from those specs on medium and low so I went looking on the forum.
http://www.candlepowerforums.com/vb/showthread.php?258156-4Sevens-Preon-Review-%281xAAA-amp-2xAAA%29-RUNTIMES-BEAMSHOTS-and-more...
Doesn't every consumer NiMH charger with a user selectable charging current work the same way? Every one I've seen including the early version of the C-9000 I tested used PWM of the full charge rate to provide the lower charging rates.
I share your concern of the higher pulsed rates but every...
Ray,
I'd be very interested in how an Energizer behaves if you put it through a few cycles charging only one battery at a time at 1000 mA in one of the outer slots.
I found the C-9000 gets batteries far hotter than I like and my past experience with chargers that do that is that I get poor...
If you're using the batteries in single cell applications just charge them and use them.
If you're using the batteries in multi cell applications, a few conditioning cycles is a good idea IMHO. New cells often exhibit low capacity for the first couple/few cycles.
From what I've observed this...
The Jetbeam C-LE I got from CEJ's group buy draws about the same power as yours.
The 2 Jetbeam C-LEs that I got from Deal Extreme draw even more power than Julesb measured. The higher of the 2 is pulling 3.3 A on high. It puts out over 90 lumens on high initially but the output starts dropping...
It's not small but a Dorcy 3D modded with an SSC is a very impressive thrower IMHO. I'm running a GD buck/boost converter configured for 833 mA and measured 26500 lux @ 1 M. 135 Lumens and a 10+ hour run time on NiMH D cells or using 4 AA to D cell adapters. Probably about 5 hours on alkalines...
The P3D head actually works pretty well with a P2D body and an RCR123 3.7 V LiOn...at least with those that fit. Depending on how well the RCR123 holds voltage under load, turbo mode run time can be short before the annoying regulator oscillation starts but run times on the lower levels should...
The "low battery warning" on the P3D is Fenix marketing speak IMHO. It's really the buck regulator going into oscillation when the battery voltage drops too low to maintain the regulated current for the level in use.
Since less voltage is required to maintain regulation on the lower levels due...
I've used the .030" copper disc from the SS on other SSC mods. Does a thinner shim work better in general or is there a particular reason in the L0x? Do you make the .015" ones yourself or is there a source for them ready made?
I just found out that I can open my L0P SE without any tools so...
I'd suggest setting it considerably lower since it's unlikely that all the batteries will reach full charge at the same time.
I try to avoid charging in series whenever possible and avoid peak charging (-dV) when it's not. That said, I'd personally set the limit to something like 5-15 mV in...
My favorite UI on a light by far is the one on the VB-16.
16 levels
turns on at last level used
separate buttons for changing the level up or down, push once quickly for a single level change or hold to ramp through all levels in a couple of seconds.
no detectable PWM on any level
It was nice...
Re: AAA Rechargeable Eneloops 36 pack/ 9.99
Amazon has 8 packs of AA Eneloops for $19.99 right now. Free shipping on orders of $25 or more.
http://www.amazon.com/exec/obidos/tg/detail/-/B000LNI5VC/ref=ord_cart_shr/102-3279289-4398511?%5Fencoding=UTF8&m=ATVPDKIKX0DER&v=glance
Mike
Virtually all DMMs will drop the voltage by ~.1 V per amp since they generally use a .1 ohm resistor in current mode and measure the voltage drop across it. Fluke is one of the few who actually spec the "voltage burden" on some of their meters. Even on the ~$400 187/189, it's about .04 V / A...
c_c,
Do you have a link for the Energizer manual? The only Energizer doc I found was fairly limited compared to the Duracell "OEM" and Sanyo tech docs.
The Duracell doc I found is here.
http://www.duracell.com/oem/rechargeable/Nickel/nickel_metal_tech.asp
Mike