Search results

Inventry
Gather App
UnlistMe
Candle Power Forums

Help Support Candle Power:

  1. D

    The Official Zebralight Thread

    That's correct. Direct from the website: "This light has 3 main levels, High, Medium, and Low. The High and Medium levels have two sub-levels."
  2. D

    The Official Zebralight Thread

    Sounds like a physical button issue, or a button debounce firmware issue.
  3. D

    Overview: All eneloop batteries; 2005-2025

    I think you're confusing Li-ion vs NiMH (eneloop). Eneloop's should be fully charged from the factory.
  4. D

    The Official Zebralight Thread

    What's your definition of LVP failing? What was the end voltage? How old are your Eneloop Pros? Have any regular Eneloops to test with? It's pretty well known that Eneloop Pros don't have nearly as many cycles as regular Eneloops and thus die (high internal resistance) much quicker. I've...
  5. D

    The Official Zebralight Thread

    I did the same earlier this morning. Ignore and move on with life. Yes, back on topic: I'm also looking forward to the 719A SC64. I'll wait until some others get them and give their opinions while I wait for it to show up at NKON. I'm still holding out hope they also do a 5000K SC64d option...
  6. D

    The Official Zebralight Thread

    If you understand the difference then why would you bring up the fact that Eneloops have 2500mAh? How does the capacity (Ah) of an Eneloop have any meaning when discussing Li-ion capacity, they're obviously a different nominal voltage. The only comparison that is relevant, when comparing...
  7. D

    The Official Zebralight Thread

    You do realize that a 14500 (usually around 1000mAh) has more energy (Wh) than a 2500 mAh NiMH AA?
  8. D

    The Official Zebralight Thread

    The ZebraLight is only two pieces, head/body (single piece) and the tail cap.
  9. D

    The Official Zebralight Thread

    Where do you come up with this nonsense? None of the stock ZebraLight clips are aluminum. They're quite bendy (hint #1) They're magnetic (hint #2)
  10. D

    The Official Zebralight Thread

    Sure, if your battery level is very low. Otherwise, @lampeDépêche is correct that it's limited by cooling and not the battery.
  11. D

    The Official Zebralight Thread

    2.45A @ 1.2V and 1.7A @ 4V BLF thread where this driver was measured: https://budgetlightforum.com/t/efficiency-measurements-of-a-few-drivers/68528 Uses an Analog Devices LTC3539-2 boost converter Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/35392fc.pdf If...
  12. D

    The Official Zebralight Thread

    Yes, it's in stock on their website. What Bob_McBob was saying is that ZL has soldered all the XHP35 HI LEDs onto drivers for SC64w HI. So, they can still continue making SC64w HIs until they run out of the drivers (with the LEDs).
  13. D

    The Official Zebralight Thread

    I also have a SC600w Plus and all 4 quadrants of the LED illuminate at the same level. Also no strangeness with the slow beacon.
  14. D

    The Official Zebralight Thread

    New SC64w HI arrived and it's a XHP35 HI for sure (not a XHP35.2 HI).
  15. D

    The Official Zebralight Thread

    https://www.reddit.com/r/flashlight/comments/mnqamh/i_ordered_a_h600w_mk_iv_and_it_doesnt_look_like/
  16. D

    The Official Zebralight Thread

    Oh, interesting, I guess I'll find out. As long as it's a HI and not a HD it should be ok?
  17. D

    The Official Zebralight Thread

    Seems like the "Proceed to Checkout" link doesn't always go correctly to the secure checkout page. Maybe try going directly to it: https://zebralight.3dcartstores.com/checkout_one.asp I ordered a SC64w HI today without issue. Better grab one before they go out of stock again. :)
  18. D

    The Official Zebralight Thread

    Follow-up question: which ones are you keeping and are your favorite? SC64w HI for EDC I assume.
  19. D

    The Official Zebralight Thread

    Thanks for the input. I'll contact NKON and see about a replacement.
  20. D

    The Official Zebralight Thread

    Yes, very strange that it's only on this single mode. I've programmed G6 and tested all modes. You won't see the flickering on the video but it does show up as the vertical black bars (rolling shutter effect). The vertical bars don't seem to have a pattern and are random which is how the...

Latest posts

Back
Top