• You must be a Supporting Member to participate in the Candle Power Forums Marketplace.

    You can become a Supporting Member.

Sold/Expired Sigma Customs

Care to add a second light for me to the bottom of the list? Al-Bronze 18500 knurled w/clip please.
 
Thetasigma said:
Done. If you get tired of waiting you could always try to pry Dell's from him...:D
Click to expand...
Hell NO!!! [emoji13]
On a side note: 18500 tube is really a good balance of size & capacity. It does feel a little heavier in the pocket but I'm sure most of you will have no qualms with that.
 
DellSuperman said:
Hell NO!!! [emoji13]
On a side note: 18500 tube is really a good balance of size & capacity. It does feel a little heavier in the pocket but I'm sure most of you will have no qualms with that.
Click to expand...

And this was the response I guessed I'd receive upon asking lol.
 
DellSuperman said:
Hell NO!!! [emoji13]
On a side note: 18500 tube is really a good balance of size & capacity. It does feel a little heavier in the pocket but I'm sure most of you will have no qualms with that.
Click to expand...

:laughing: It is headed back to you at any rate. The 18500 is my personal favorite format, good balance, plenty of length, and decent capacity.
 
Please change me to Aluminum Bronze, 18500. If it becomes available in 18650 I'll go for that. But the material is more important. :thanks:
 
Unless I've misunderstood, the interest/order list seems to be open-ended. Can I take a spot at the end of the line? 18650/brass/knurled/tapped for clip screws/narrow clear optic/sapphire/green o-rings/glow sticker. I would gladly pay a premium for a titanium version if that becomes a possibility. I'd also be interested in Al-bronze if that's ever viable in the 18650 format. Is tumbled finish still an option?
 
Last edited:
StrayLight said:
Unless I've misunderstood, the interest/order list seems to be open-ended. Can I take a spot at the end of the line? 18650/brass/knurled/tapped for clip screws/narrow clear optic/sapphire/green o-rings/glow sticker. I would gladly pay a premium for a titanium version if that becomes a possibility. I'd also be interested in Al-bronze if that's ever viable in the 18650 format. Is tumbled finish still an option?
Click to expand...

The list was originally capped, but I was unable to get it done in the time I wanted, so I have left the list open ended for now and it is fulfilled as I get the time.
Titanium is unlikely with my current setup, and even if I did it on the current lathe it would be very time consuming. I won't be making any more Al-Bronze in 18650 with the current machine either. I do not currently offer any finishing or aesthetic treatments aside from the brushing I do to finished hosts.

Shop time has been scarce the last couple months but things are clearing up a bit so I should get a few lights done between here and the new year. Any lights completed by the new year will probably be shipped early January.
 
Please add me to the list, 18500, copper, ringed, clip, narrow, blue rings/sticker/boot. Thanks!
 
Can I be added for 1 Copper and 1 Brass!! (18650, Ringed, 219c, H17F, 10507, Blue O-Rings and Sapphire Lenses - All on both Please!!) Thank You!

Steve
 
Last edited:
Would there be any interest for Serge's 371D driver? It is the same driver/XP-L 4000k combo that is in the Overready Wasp and BOSS.

They offer extremely good efficiency in all modes (90-97% efficiency per Serge), current controlled, secondary red LED, bounce sensor, fully programmable, on board temperature regulation, and wide voltage range 1-2 cells.
I'm thinking of offering these as an option in addition to the standard H17F. They are very expensive though, so additional cost would be +$50 for that setup.
 
Thetasigma said:
Would there be any interest for Serge's 371D driver? It is the same driver/XP-L 4000k combo that is in the Overready Wasp and BOSS.

They offer extremely good efficiency in all modes (90-97% efficiency per Serge), current controlled, secondary red LED, bounce sensor, fully programmable, on board temperature regulation, and wide voltage range 1-2 cells.
I'm thinking of offering these as an option in addition to the standard H17F. They are very expensive though, so additional cost would be +$50 for that setup.
Click to expand...
I'd go for that.
 
I would definitely go for Serge's driver. I had one of the new Oveready V5 lights and loved the programming interface.

This should also take care of the worries of over current on the switch I would think.
 
You must log in or register to reply here.

Latest posts

Back
Top